Designing oligomeric ethylene terephtalate building blocks by chemical recycling of polyethylene terephtalate

The intelligent recycling of plastics waste is a major concern. Because of the widespread use of polyethylene terephtalate, considerable amounts of PET waste are generated that are ideally re‐introduced into the material cycle by generating second generation products without loss of materials performance. Chemical recycling methods are often expensive and entail environmentally hazardous by‐products. Established mechanical methods generally provide materials of reduced quality, leading to products of lower quality. These drawbacks can be avoided by the development of new recycling methods that provide materials of high quality in every step of the production cycle. In the present work, oligomeric ethylene terephthalate with defined degrees of polymerization and defined molecular weight is produced by melt‐mixing PET with different quantities of adipic acid as an alternative pathway of recycling PET with respect to conventional methods, offering ecofriendly and economical aspects. Additionally, block‐copolyesters of defined block length are designed from the oligomeric products. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39786.     

Analyses of structurally modified quasi‐solid‐state electrolytes using electrochemical impedance spectroscopy for dye‐sensitized solar cells

Electrochemical properties of structurally modified quasi‐solid‐state electrolytes were examined using porous substrates (PSs). The PS was prepared into two categories by a phase inversion method with a brominated poly(phenylene oxide) (BPPO): the sponge and finger types. Effects of the humidification and cosolvent compositions on the morphology of the PS were analyzed by scanning electron microscopy. In all cases of the PSs, a higher V_OC was observed of about 0.1 V than that of a liquid electrolyte owing to a suppressed back electron charge transfer. In addition, the PS prepared by the polymer solution of 1 : 4 : 1 (BPPO : N‐methyl‐2‐pyrrolidone : butyl alcohol) with the humidification process showed better photovoltaic properties in terms of the current density and conversion efficiency owing to the appropriate combinations of pore size, tortuosity, and interconnectivity. Effects of the pore structures were intensively examined using electrochemical impedance spectroscopy. The impedance results revealed that large pores at the surface layers are advantageous for a lower R_S and R_TiO2. Meanwhile, the straight inner structure is beneficial for the facile I^?/I₃^? diffusion, thus lowering R_Pt. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39739.     

Powder coating of veneered particle board surfaces by hot pressing

The powder coating of veneered particle boards by the sequence electrostatic powder application – powder curing via hot pressing is studied in order to create high gloss surfaces. To obtain an appealing aspect, veneer sheets were glued by heat and pressure on top of particle boards and the resulting surfaces were used as carrier substrates for powder coat finishing. Prior to the powder coating, the veneered particle board surfaces were pre-treated by sanding to obtain good uniformity and the boards were stored in a climate chamber at controlled temperature and humidity conditions to adjust an appropriate electrical surface resistance. Characterization of surface texture was done by 3D microscopy. The surface electrical resistance was measured for the six veneers before and after their application on the particle board surface. A transparent powder top-coat was applied electrostatically onto the veneered particle board surface. Curing of the powder was done using a heated press at 130 °C for 8 min and a smooth, glossy coating was obtained on the veneered surfaces. By applying different amounts of powder the coating thickness could be varied and the optimum amount of powder was determined for each veneer type.     

Holzbrücken – Erkenntnisse zum Feuchteverhalten in den Tragquerschnitten aus Langzeitmessungen

Timber bridges – Long term monitoring results of moisture diffusion in the load carrying cross‐sections Timber road bridges have been built worldwide for centuries. The high performance of wood is approved through many constructions. However, there are still doubts about using wood by the planning engineer, which reduce the number of realized projects. The moisture induced stresses in cross‐sections according to the varied ambient climate are mainly investigated under laboratory conditions. The results show that the moisture content changes differently over the cross‐section and leads to moisture induced stresses. The discussion about methods for the assessment of the moisture induced stresses in timber bridge cross‐ections is continuing. Results observed in the long term monitoring of seven timber bridges provide first guidelines for practitioners. For all constructions, the moisture content was measured regarding the ambient micro climate. As result, the influences according to the ambient micro climate are not insignificant. Positive is that the directly measured moisture content is less compared to the equilibrium moisture content calculated from the data of a close by meteorological station. The analysis of the moisture gradient over the cross‐section allows the definition of an active or passive zone.     

Endogenous Nitric-Oxide Synthase Inhibitor ADMA after Acute Brain Injury

Previous results on nitric oxide (NO) metabolism after traumatic brain injury (TBI) show variations in NO availability and controversial effects of exogenous nitric oxide synthase (NOS)-inhibitors. Furthermore, elevated levels of the endogenous NOS inhibitor asymmetric dimethylarginine (ADMA) were reported in cerebro-spinal fluid (CSF) after traumatic subarachnoid hemorrhage (SAH). Therefore, we examined whether ADMA and the enzymes involved in NO- and ADMA-metabolism are expressed in brain tissue after TBI and if time-dependent changes occur. TBI was induced by controlled cortical impact injury (CCII) and neurological performance was monitored. Expression of NOS, ADMA, dimethylarginine dimethylaminohydrolases (DDAH) and protein-arginine methyltransferase 1 (PRMT1) was determined by immunostaining in different brain regions and at various time-points after CCII. ADMA and PRMT1 expression decreased in all animals after TBI compared to the control group, while DDAH1 and DDAH2 expression increased in comparison to controls. Furthermore, perilesionally ADMA is positively correlated with neuroscore performance, while DDAH1 and DDAH2 are negatively correlated. ADMA and its metabolizing enzymes show significant temporal changes after TBI and may be new targets in TBI treatment.     

Proximal schemes for parabolic optimal control problems with sparsity promoting cost functionals

Fast first-order proximal methods that solve linear and bilinear parabolic optimal control problems with a sparsity cost functional are discussed. Weak convergence of these methods is proved and, for benchmarking purposes, the proposed inexact proximal schemes are compared to an inexact semi-smooth Newton method. Results of numerical experiments are presented to demonstrate the computational effectiveness of proximal schemes and to validate the theoretical estimates.     

Vergleich des Stofftransports von hängenden und akustisch levitierten Wassertropfen in CO2

High‐pressure acoustic levitation devices allows a contact‐free investigation of liquids. Here, acoustically levitated water droplets and pendant water droplets were examined in regards to the mass transfer coefficient in a static CO₂‐atmosphere under elevated pressures. Based on the droplet geometry and the decrease of the droplet volume over time, it was possible to calculate the mass transfer coefficient of water into CO₂ at any given time. Additionally, open questions regarding possible differences between pendant and acoustically levitated water droplets were discussed.     

Deposition welding of hot forging dies using nanoparticle reinforced weld metal

In the application field of forging, the form-giving tool components are subject to process-related severe environmental conditions, such as high mechanical loads acting simultaneously with high tribological and thermal charges. Due to high machine hour rates as well as increasing environmental requirements in terms of energy consumption, wear protection methods and suitable repair measures for forging tools become more and more important. Laser deposition welding represents an established process for the repair of complex shaped surfaces. A new approach is the addition of nano-sized ceramic particles to improve the mechanical properties. The main idea is to reduce the grain size of the cladded layers by adding nano-sized nuclei. A fine grained microstructure will improve strength as well as ductility and fatigue resistance. Furthermore small hard particles can improve the wear resistance without affecting the friction of the surface. After the cladding process the surface has to be finished usually by turning, milling and grinding operations. Within the presented paper the potential of nanoparticle-reinforced deposition welding with regard to increasing the wear resistance of forging dies will be examined. First, the process of nanoparticle-reinforced deposition welding will be presented. Afterwards it will be shown that yttrium oxide, titanium carbide and tungsten carbide nanoparticles in an AISI H10 matrix material will influence the friction coefficient between forging tool and material as well as the wear properties.